To get to it, the first step is to remove the tank lid. To lower the water level in the top toilet tank with the float arm or lift arm , make sure to loosen or tighten the screw until the float arm with the float ball or float cup drops to the right level.
To lower the water level in a toilet tank with a column float attached to the fill valve, loosen the screw or clip and then push down the float arm with the float ball to the right level on the fill valve and tighten everything back up again. If the running stops, you have found your problem. Also, check that the float tank ball is not touching the tank wall.
You could fix the issue but just making sure it isn't getting stuck on the sidewall. This will ensure the level is lower than the overflow tube and stop a running toilet.
Fill valves are cheap and relatively simple to replace, so if this isn't working, replace the entire valve assembly.
The second most common reason for a running toilet is a deteriorated toilet flapper valve or valve seal. The flapper's job is to seal the water in the tank.
When toilet flappers get too old, they don't seal the way they are supposed to , allowing water to continually pass from the toilet top tank down into the toilet bowl. To replace the flapper, remove the old one and replace it with a new one that you can purchase from any hardware store.
You can remove it by detaching the flapper chain or lift wire and taking the flapper off the mounting pins on the side of the overflow tube. Tip for DIY newbies: Drain all the water from the tank first before replacing the toilet flapper. You can do this by shutting off the water supply that feeds the top tank and then flushing the toilet to drain the remaining water. Another Tip: If the chain is too long, it could be getting caught underneath the flapper as the tank empties.
Your toilet could be running because the flapper isn't getting a good seal. So shorten it while you are in there poking around. The third cause of your running toilet could be that the refill tube or overflow pipe is continually pumping water into the bowl.
This can happen when the fill tube is too long and isn't positioned correctly in the overflow tube. To shorten a tube, pull out the toilet overflow tube from the overflow and hold it just above the overflow opening. Trim it right there and then clip it to the side of the overflow tube.
This will keep it in the right place. Quick Note: This can cause the toilet to run because the refill valve is creating a suction effect that pulls water out of the fill valve.
Now that you're all done. Turn on the water supply allowing water back into the toilet tank. Flush the toilet once it's full and check for leaks.
Also, check the water line level to ensure it refills to the right level. We strongly advise that you contact an expert plumber to inspect the situation for you, as there could be other issues with your toilet that may need repair and maintenance. However, that doesn't mean that you can't inspect your toilet yourself!
Here are some things that you can do to help fix your running toilet in the meantime. Among the most common causes for a running toilet is overflow water leaking down into the bowl from the tank via the overflow tube. This happens when there's too much water in the tank. You can adjust the water level by adjusting the height of the float.
To lower the water in a toilet with a float arm, loosen or tighten the screw until the float arm lowers.
To lower the water in a toilet with a column float attached to the fill valve, loosen the screw or clip, push down the float, and tighten everything back up again. Perhaps the most common reason for a running toilet is an old flapper that needs to be replaced. To replace the flapper, simply remove the old one and replace it with a new one from the hardware store.
Remove the old one by detaching the chain and taking the flapper off the pins on the side of the overflow tube. A float cup fill valve has a small cylinder wrapped around the fill valve. The cylinder float cup slides up and down the valve shaft and determines the water level via its height. To do so on a float ball fill valve, there will be a screw on top of the valve for adjustments. Use a screwdriver to turn this a quarter turn counterclockwise in order to lower the float.
For a float cup fill valve, do the same as above and turn the screw a quarter turn counterclockwise to reduce the height of the float. After completing the above, flush and refill the toilet tank. Check the water level; an ideal height for your water level is 1 to 1.
Step 3 If the toilet water is running intermittently, have a look at the fill tube. This is a tube attached to the fill valve that fills your toilet tank with water after flushing. This should always be above the water line to prevent intermittent running. Check this is above the water level when the tank is full, and if not then be sure to trim the tube so it does sit above the water line. An incorrectly adjusted or faulty float can disrupt the effectiveness of your toilet tank and likely mean that the toilet keeps running.
Shake the float itself and listen for any water moving around inside. Pop into your local hardware store or order a new float online and things should be right as rain in no time. A faulty fill valve can often be the root of the problem when your toilet keeps running. Step 1 Shut off your water and drain your tank fully, using a sponge to soak up any excess water remaining at the bottom of the tank.
Step 2 Disconnect the water supply to your toilet by unscrewing the lock nut securing your water supply line into place. Step 3 Remove the old fill valve. Remove this by using an adjustable wrench and turning the lock nut counterclockwise.
Take this with you to the hardware store so they can help you find the best fit. Step 4 Install the new fill valve and connect the water. Pop your new fill valve into the same place you removed the old one, connect the water supply line, and tighten the nut clockwise until secure.
0コメント